-
1 through fault current
ток внешнего повреждения
ток внешнего замыкания
Ток, вызванный повреждением в энергосистеме, внешним по отношению к участку, защищаемому данной защитой, и протекающий через этот защищаемый участок
[Разработка типовых структурных схем микропроцессорных устройств РЗА на объектах ОАО "ФКС ЕЭС". Пояснительная записка. Новосибирск 2006 г.]EN
through fault current
a current due to a power system fault external to that part of the section protected by the given protection and which flows through the protected section
[IEV ref 448-13-13]FR
courant de défaut traversant
courant dû à un défaut dans le réseau d'énergie à l'extérieur de la section protégée par la protection considérée et qui circule dans cette section protégée
[IEV ref 448-13-13]Тематики
Синонимы
EN
DE
- Durchgangsstrom (bei äußerem Netzfehler), m
FR
Англо-русский словарь нормативно-технической терминологии > through fault current
-
2 through fault current
Автоматика: сквозной ток повреждения -
3 through-fault current
Техника: ток сквозного КЗ -
4 through fault current
English-Russian dictionary of relay protection > through fault current
-
5 fault current
аварийный ток
IΔ
Ток, утекающий на землю вследствие повреждения изоляции
[ ГОСТ Р 61557-1-2006]EN
fault current
IΔ
current flowing to earth due to an insulation fault
[IEC 61557-6, ed. 2.0 (2007-07)]FR
courant de défaut
IΔ
courant qui s'écoule à la terre lors d'un défaut d'isolement
[IEC 61557-6, ed. 2.0 (2007-07)]Тематики
- электротехника, основные понятия
EN
ток короткого замыкания
Сверхток, появляющийся в результате короткого замыкания, вызываемого повреждением или неправильным соединением в электрической цепи.
МЭК 60050(441-11-07)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
ток короткого замыкания
Сверхток, обусловленный замыканием с ничтожно малым полным сопротивлением между точками, которые в нормальных условиях эксплуатации должны иметь различный потенциал.
Примечание — Ток короткого замыкания может явиться результатом повреждения или неправильного соединения
(МЭС 441—11—07)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
ток короткого замыкания
Электрический ток в данной короткозамкнутой цепи.
[ ГОСТ Р МЭК 60050-195-2005]
ток короткого замыкания (Ic)
Сверхток, появляющийся в результате короткого замыкания, вследствие повреждения или неправильного соединения в электрической цепи
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
ток короткого замыкания
Электрический ток при данном коротком замыкании.
[ ГОСТ Р МЭК 60050-826-2009]
ток короткого замыкания
Сверхток, возникающий в результате короткого замыкания из-за дефекта или неправильного подключения в электрической цепи.
[ ГОСТ Р МЭК 60204-1-2007]EN
short-circuit current
an over-current resulting from a short circuit due to a fault or an incorrect connection in an electric circuit
[IEV number 441-11-07]
short-circuit current
electric current in a given short-circuit
Source: 603-02-28 MOD
[IEV number 195-05-18]
[IEV number 826-11-16]FR
courant de court-circuit
surintensité résultant d'un court-circuit dû un défaut ou à un branchement incorrect dans un circuit électrique
[IEV number 441-11-07
courant de court-circuit
courant électrique dans un court-circuit déterminé
Source: 603-02-28 MOD
[IEV number 195-05-18]
[IEV number 826-11-16]
Рис. 7 (Рис. ABB)
Контур тока короткого замыкания при замыкании на землю в системе ТТ
1 - Вторичная обмотка трансформатора;
2 - Линейный проводник;
3 - Сопротивление в месте замыкания;
4 - Проводник защитного заземления;
5 - Зазеамляющий электрод электроустановки;
6 - Заземляющий электрод нейтрали вторичной обмотки тарнсформатораПараллельные тексты EN-RU
An earth fault in a TT system originates the circuit represented in Figure 7.
The fault current flows through the secondary winding of the transformer, the line conductor, the fault resistance, the protective conductor, and the earth electrode resistances (RA, of the user’s plant, and RB, of the neutral).
[ABB]Замыкание на землю в системе TT образует цепь, представленную на рисунке 7.
Ток короткого замыкания протекает через вторичную обмотку трансформатора, линейный проводник, сопротивление в месте замыкания, проводник защитного заземления, заземляющие электроды (RA электроустановки и RB нейтрали вторичной обмотки трансформатора).
[Перевод Интент]Тематики
- электробезопасность
- электротехника, основные понятия
- электроустановки
EN
DE
FR
ток повреждения
Ток, возникающий в результате пробоя или перекрытия изоляции.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
ток повреждения
Ток, который протекает через данную точку повреждения в результате повреждения изоляции.
[ ГОСТ Р МЭК 60050-826-2009]EN
fault current
current resulting from an insulation failure, the bridging of insulation or incorrect connection in an electrical circuit
[IEC 61439-1, ed. 2.0 (2011-08)]
fault current
current which flows across a given point of fault resulting from an insulation fault
[IEV number 826-11-11]FR
courant de défaut
courant résultant d'un défaut de l'isolation, du contournement de l’isolation ou d’un raccordement incorrect dans un circuit électrique
[IEC 61439-1, ed. 2.0 (2011-08)]
courant de défaut, m
courant s'écoulant en un point de défaut donné, consécutivement à un défaut de l'isolation
[IEV number 826-11-11]Тематики
EN
DE
- Fehlerstrom, m
FR
- courant de défaut, m
3.1 аварийный ток (fault current) ID: Ток, проходящий в землю вследствие повреждения изоляции.
Источник: ГОСТ Р МЭК 61557-6-2009: Сети электрические распределительные низковольтные напряжением до 1000 В переменного тока и 1500 В постоянного тока. Электробезопасность. Аппаратура для испытания, измерения или контроля средств защиты. Часть 6. Устройства защитные, управляемые дифференциальным током, в TT и TN системах оригинал документа
3.6.1 аварийный ток (fault current) IΔ: Ток, утекающий на землю вследствие повреждения изоляции.
Источник: ГОСТ Р МЭК 61557-1-2005: Сети электрические распределительные низковольтные напряжением до 1000 В переменного тока и 1500 В постоянного тока. Электробезопасность. Аппаратура для испытания, измерения или контроля средств защиты. Часть 1. Общие требования оригинал документа
Англо-русский словарь нормативно-технической терминологии > fault current
-
6 fault
1) повреждение; отказ; неисправность; неполадка2) дефект3) ошибка4) сдвиг ( горной породы)6) пищ. лесн. порок•-
antiphase boundary fault
-
arcing fault
-
arcing ground fault
-
automatically repair fault
-
braking fault
-
cable fault
-
clean stacking fault
-
close-in fault
-
contact fault
-
core-to-core fault
-
dead earth fault
-
disconnection fault
-
dislocation-initiated stacking faults
-
double-ground fault
-
double-line-to-ground fault
-
double-line-to-neutral fault
-
double-phase-to-ground fault
-
earth fault
-
electrical fault
-
equivalent fault
-
external fault
-
extrinsic stacking fault
-
frequently occurring fault
-
ground fault
-
growth fault
-
hardware fault
-
heavy-current fault
-
image fault
-
improbable fault
-
insulation fault
-
intermittent fault
-
internal fault
-
intrinsic stacking fault
-
ironwork fault
-
latent fault
-
line fault
-
line-to-earth fault
-
line-to-line fault
-
logic fault
-
molding fault
-
one-line open fault
-
open-phase fault
-
oxidation-induced stacking faults
-
oxidation stacking faults
-
page fault
-
permanent fault
-
phase fault
-
phase-to-ground fault
-
phase-to-phase fault
-
physical fault
-
pipe fault
-
pole-to-earth fault
-
pole-to-pole fault
-
primary fault
-
program-sensitive fault
-
pseudotransient fault
-
secondary fault
-
self-clearing fault
-
series fault
-
sessile fault
-
short-line fault
-
shunt fault
-
single line-to-earth fault
-
single phase-to-ground fault
-
single-phase line-to-ground fault
-
solid fault
-
spot fault
-
stacking fault
-
subsequent faults
-
superlattice fault
-
sustained fault
-
symmetrical fault
-
three-phase fault
-
through fault
-
transient fault
-
turn-to-turn fault
-
twin fault
-
two-lines open fault
-
weak-current arcing fault -
7 current
1) течение; поток4) вчт. текущая запись•-
absorption current
- ac anode current -
action current
-
active current
-
actuating current
-
admissible continuous current
-
air current
-
alongshore current
-
alternate current
-
anode current
-
arbitrary noise current
-
arc current
-
arc-back current
-
arcing ground fault current
-
armature current
-
ascending current
-
audio-frequency current
-
avalanche current
-
back current
-
back short circuit current
-
backward current
-
barogradient current
-
base current
-
beam current
-
bearing currents
-
beating current
-
beat current
-
biasing current
-
bias current
-
biphase current
-
bleeder current
-
blind current
-
blowing current
-
body current
-
bottom current
-
boundary current
-
braking current
-
branch current
-
break induced current
-
breakaway starting current
-
breakdown current
-
breaking current
-
bucking current
-
bulk current
-
bypass current
-
capacitance current
-
capacitive current
-
capacity current
-
carrier current
-
cathode current
-
channel current
-
charging current
-
circulating current
-
circumpolar current
-
collector current
-
complex sinusoidal current
-
complex current
-
conduction current
-
conjugate complex sinusoidal current
-
conjugate complex current
-
constant current
-
consumption current
-
continuous current
-
continuous traction current
-
control current
-
convection current
-
core-loss current
-
creeping current
-
critical current
-
cross current
-
crystal current
-
current of realm
-
current of run-unit
-
current of set
-
cutoff current
-
damped alternating current
-
damped current
-
dark current
-
deep-water current
-
deep current
-
delta currents
-
density current
-
descending current
-
design current
-
dielectric absorption current
-
dielectric current
-
diffusion current
-
direct current
-
direct-axis current
-
discharge current
-
discontinuous current
-
displacement current
-
downward current
-
drift current
-
drive current
-
drop-away current
-
earth current
-
earth fault current
-
eddy currents
-
effective current
-
electric current
-
electrode current
-
electrolysis current
-
electron current
-
electron-beam induced current
-
emission current
-
emitter current
-
equalizing current
-
equivalent input noise current
-
excess current
-
exchange current
-
excitation current
-
external current
-
extra current
-
extraction current
-
extraneous current
-
feedback current
-
field current
-
filament current
-
firing current
-
flood current
-
fluctuating current
-
focusing-coil current
-
focus current
-
fold back current
-
follow current
-
forced alternating current
-
forced current
-
foreign currents
-
forward current
-
Foucault currents
-
free alternating current
-
free current
-
full-load current
-
fusing current
-
galvanic current
-
gas current
-
gate current
-
gate nontrigger current
-
gate trigger current
-
gate turnoff current
-
generation-recombination current
-
gradient current
-
grib current
-
ground current
-
ground-return current
-
harmonic current
-
heat current
-
heater current
-
high-frequency current
-
high-level input current
-
high-level output current
-
holding current
-
hold current
-
hold-on current
-
hole current
-
idle current
-
image current
-
impressed current
-
incident current
-
induced current
-
initial current
-
injection current
-
inphase current
-
input current
-
input leakage current
-
input offset current
-
inrush current
-
inshore current
-
instantaneous carrying current
-
instantaneous current
-
insulation current
-
interference current
-
intermittent current
-
inverse current
-
ion production current
-
ionic current
-
ion current
-
ionization current
-
irradiation-saturation current
-
lagging current
-
latching current
-
leading current
-
leakage current
-
let-go current
-
light current
-
lightning current
-
line charging current
-
linear current
-
load current
-
locked-rotor current
-
loop current
-
loss current
-
low-level input current
-
low-level output current
-
magnetization current
-
majority-carrier current
-
majority current
-
make induced current
-
make-and-brake current
-
making current
-
maximum power current
-
minority-carrier current
-
minority current
-
motor inrush current
-
nearshore current
-
near-surface current
-
net current
-
neutral current
-
neutron current
-
neutron diffusion current
-
noise current
-
no-load current
-
nonsinusoidal current
-
nontrigger current
-
non-turn-off
-
offset current
-
offshore current
-
off-state current
-
on-state current
-
open-circuit current
-
operating current
-
output current
-
overload current
-
parasitic current
-
peak arc current
-
peak current
-
peak switching current
-
peak withstand current
-
peak-point current
-
peak-to-peak current
-
perception current
-
periodic current
-
persistent current
-
phase current
-
phase-fault current
-
phasor current
-
photo-electric current
-
photo current
-
photo-generated current
-
photo-induced current
-
pickup current
-
piezoelectric current
-
pinch current
-
plasma current
-
polarization current
-
polyphase current
-
postarc current
-
power current
-
power follow current
-
prebreakdown current
-
preconduction current
-
primary current
-
principal current
-
probe current
-
pull-in current
-
pulsating current
-
pulse current
-
pyroelectric current
-
quadrature-axis current
-
quiescent current
-
rated current
-
rated temperature-rise current
-
reactive current
-
read current
-
recombination current
-
rectified current
-
reflected current
-
regulated current
-
relative short-circuit current
-
release current
-
residual current
-
rest current
-
return current
-
reverse current
-
reverse-biased current
-
reverse-induced current
-
RF current
-
ringing current
-
rip current
-
ripple current
-
root-mean-square current
-
running current
-
rupturing current
-
saturated drain current
-
saturation current
-
saw-tooth current
-
secondary current
-
secondary-electron emission current
-
shaft currents
-
sheath current
-
shelf current
-
shield current
-
shock current
-
short-circuit current
-
short-noise current
-
short-time thermal current
-
short-time withstand current
-
sine-wave current
-
single-phase current
-
sinusoidal current
-
slope current
-
sneak current
-
spindle-motor current
-
split current
-
stalled-motor current
-
standby current
-
standing current
-
star currents
-
starter current
-
steady leakage current
-
steady surface current
-
steady volume current
-
steady-state current
-
stray current
-
stroke current
-
subsurface current
-
subsynchronous frequency current
-
subsynchronous current
-
subtransient armature current
-
superconduction current
-
superimposed current
-
supply current
-
surface current
-
surface-leakage current
-
surge current
-
suspension current
-
sustained current
-
sustaining current
-
switched current
-
switching current
-
symmetrical alternate current
-
synchronizing current
-
telluric current
-
test current
-
thermal current
-
thermal noise current
-
thermionic current
-
thermostimulated current
-
three-phase current
-
threshold current
-
through current
-
tidal current
-
tolerance current
-
traction current
-
traffic current
-
transfer current
-
transient current
-
transient-decay current
-
transmission-line current
-
trigger current
-
turbidity current
-
turnoff current
-
turn-on current
-
two-phase current
-
undulating current
-
unidirectional current
-
unsymmetrical currents
-
upward current
-
valley point current
-
variable current
-
vector current
-
virtual current
-
voice-frequency current
-
voltaic current
-
wattful current
-
wattless current
-
welding current
-
whirling currents
-
wind current
-
withdrawal current
-
working current
-
work current
-
Zener current
-
zero-sequence current -
8 fault
1. дефект; повреждение2. ошибка -
9 short-circuit current
- ток короткого замыкания интегральной микросхемы
- ток короткого замыкания (в измерительной аппаратуре)
- ток короткого замыкания
ток короткого замыкания
Сверхток, появляющийся в результате короткого замыкания, вызываемого повреждением или неправильным соединением в электрической цепи.
МЭК 60050(441-11-07)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
ток короткого замыкания
Сверхток, обусловленный замыканием с ничтожно малым полным сопротивлением между точками, которые в нормальных условиях эксплуатации должны иметь различный потенциал.
Примечание — Ток короткого замыкания может явиться результатом повреждения или неправильного соединения
(МЭС 441—11—07)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
ток короткого замыкания
Электрический ток в данной короткозамкнутой цепи.
[ ГОСТ Р МЭК 60050-195-2005]
ток короткого замыкания (Ic)
Сверхток, появляющийся в результате короткого замыкания, вследствие повреждения или неправильного соединения в электрической цепи
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
ток короткого замыкания
Электрический ток при данном коротком замыкании.
[ ГОСТ Р МЭК 60050-826-2009]
ток короткого замыкания
Сверхток, возникающий в результате короткого замыкания из-за дефекта или неправильного подключения в электрической цепи.
[ ГОСТ Р МЭК 60204-1-2007]EN
short-circuit current
an over-current resulting from a short circuit due to a fault or an incorrect connection in an electric circuit
[IEV number 441-11-07]
short-circuit current
electric current in a given short-circuit
Source: 603-02-28 MOD
[IEV number 195-05-18]
[IEV number 826-11-16]FR
courant de court-circuit
surintensité résultant d'un court-circuit dû un défaut ou à un branchement incorrect dans un circuit électrique
[IEV number 441-11-07
courant de court-circuit
courant électrique dans un court-circuit déterminé
Source: 603-02-28 MOD
[IEV number 195-05-18]
[IEV number 826-11-16]
Рис. 7 (Рис. ABB)
Контур тока короткого замыкания при замыкании на землю в системе ТТ
1 - Вторичная обмотка трансформатора;
2 - Линейный проводник;
3 - Сопротивление в месте замыкания;
4 - Проводник защитного заземления;
5 - Зазеамляющий электрод электроустановки;
6 - Заземляющий электрод нейтрали вторичной обмотки тарнсформатораПараллельные тексты EN-RU
An earth fault in a TT system originates the circuit represented in Figure 7.
The fault current flows through the secondary winding of the transformer, the line conductor, the fault resistance, the protective conductor, and the earth electrode resistances (RA, of the user’s plant, and RB, of the neutral).
[ABB]Замыкание на землю в системе TT образует цепь, представленную на рисунке 7.
Ток короткого замыкания протекает через вторичную обмотку трансформатора, линейный проводник, сопротивление в месте замыкания, проводник защитного заземления, заземляющие электроды (RA электроустановки и RB нейтрали вторичной обмотки трансформатора).
[Перевод Интент]Тематики
- электробезопасность
- электротехника, основные понятия
- электроустановки
EN
DE
FR
ток короткого замыкания
Ik
Ток, протекающий через накоротко замкнутые зажимы измерительной аппаратуры
[ ГОСТ Р 61557-1-2006]Тематики
- измерение электр. величин в целом
EN
ток короткого замыкания интегральной микросхемы
ток короткого замыкания
Выходной ток интегральной микросхемы при закороченном выходе.
Обозначение
Iкз
IOS
[ ГОСТ 19480-89]Тематики
Синонимы
EN
FR
3.14 ток короткого замыкания (short-circuit current); Ik:Ток, протекающий через накоротко замкнутые зажимы измерительной аппаратуры.
Источник: ГОСТ Р 54127-1-2010: Сети электрические распределительные низковольтные напряжением до 1000 В переменного тока и 1500 В постоянного тока. Электробезопасность. Аппаратура для испытания, измерения или контроля средств защиты. Часть 1. Общие требования оригинал документа
3.1.14 ток короткого замыкания (short-circuit current) Ik: Ток, протекающий через накоротко замкнутые зажимы измерительной аппаратуры.
Источник: ГОСТ Р МЭК 61557-1-2005: Сети электрические распределительные низковольтные напряжением до 1000 В переменного тока и 1500 В постоянного тока. Электробезопасность. Аппаратура для испытания, измерения или контроля средств защиты. Часть 1. Общие требования оригинал документа
3.2.3 ток короткого замыкания (short-circuit current): Сверхток, обусловленный замыканием с ничтожно малым полным сопротивлением между точками которые в нормальных условиях эксплуатации должны иметь разный потенциал.
[МЭС 441-14-07]
Примечание - Ток короткого замыкания может явиться результатом повреждения или неправильного соединения.
Источник: ГОСТ Р 50345-2010: Аппаратура малогабаритная электрическая. Автоматические выключатели для защиты от сверхтоков бытового и аналогичного назначения. Часть 1. Автоматические выключатели для переменного тока оригинал документа
3.1.3 ток короткого замыкания (short-circuit current): Сверхток, появляющийся в результате короткого замыкания, вызываемого повреждением или неправильным соединением в электрической цепи.
[МЭК 60050(441-11-07)]
Источник: ГОСТ Р 51731-2010: Контакторы электромеханические бытового и аналогичного назначения оригинал документа
Англо-русский словарь нормативно-технической терминологии > short-circuit current
-
10 arc fault
- "дуговая" неисправность
"дуговая" неисправность
Неисправность, приводящая к возникновению дуги.
[Интент]Параллельные тексты EN-RU
An arc fault occurs when there is a reduction in the dielectric strength of the insulating means (air, in LV switchboards) interposed between two or more conducting elements at different potential.
The arc is generated at the moment when, due to the high ionization of the air, there is a breakdown of the dielectric of the medium and the consequent flow of the current through it.
In an arc fault the highest stresses are of thermal type and proportional to RaI2 owing to the high value taken by the arc resistance Ra; this because the fault current flows in a medium which is always insulating, even if extremely ionized.
Such stresses manifest themselves essentially in the form of:
• high thermal gradients caused by the quick and intense rise in the air temperature;
• high pressure gradients in the form of pressure wave;
• high ionization of the air with consequent reduction of its insulating strength.
Generally speaking, in a LV assembly designed and tested according to the Standard IEC 60439-1 an arc fault is not very likely to occur; however, should it occur, the consequences would be extremely harmful to both the equipment as well as the personnel (see Chapters 2.2 and 2.3).
The causes of an arc fault can be both technical as well as non technical; among the latter the most frequent are the following:
• personnel errors, above all during maintenance operations;
• installation operations not sufficiently accurate;
• inadequate maintenance, above all in the case of severe environmental conditions.
Among the technical causes of an arc fault in a LV assembly the following ones are to be remembered:
• breakdown of the insulation essentially in the proximity of the supports of the busbars and of the plug-in contacts of the withdrawable units (75% of cases);
• overvoltages generating disruptive discharges between the points at minimum clearances (15% of cases);
• constructional defects of the apparatus (10% of cases).
[ABB]К «дуговой» неисправности, относится неисправность, обусловленная уменьшением электрической прочности изолирующей среды (воздуха в НКУ) между двумя или более токоведущими частями, находящимися под разными электрическими потенциалами.
Дуга образуется в тот момент, когда вследствие высокой ионизации воздуха происходит пробой изолирующей среды, вследствие чего через нее начинает протекать электрический ток.
Проявлением дуговой неисправности, является тепловое воздействие, пропорциональное RaI2 и достигающее большого значения вследствие большого сопротивления дуги Ra.
Дело в том, что ток дуги протекает через среду, которая всегда является изолирующей, пусть даже и чрезвычайно ионизированной.
Указанные воздействия очевидны сами по себе особенно в форме:
• теплового градиента температуры, вызванного быстрым и интенсивным подъемом температуры воздуха;
• высоким градиентом давления в форме волны давления;
• высокой ионизацией воздуха с последующим уменьшением электрической прочности.
Вообще говоря, в НКУ, разработанных и испытанных в соответствии с требованиями стандарта МЭК 60439-1 «дуговая» неисправность маловероятна. Однако, если дуга все таки возникнет, ее последствия буду чрезвычайно тяжелыми как для оборудования, так и для персонала (см. п. 2.2 и 2.3).
Причина дуговой неисправности может носить как технический, так и нетехнический характер. Среди последних наиболее часто возникают следующие:
• ошибки персонала, совершаемые главным образом во время технического обслуживания;
• недостаточно аккуратное выполнение монтажа;
• ненадлежащее техническое обслуживание, главным образом при эксплуатации НКУ в тяжелых условиях окружающей среды.
Среди технических причин дуговой неисправности в НКУ необходимо помнить о следующих:
• пробой изоляции, особенно вблизи опор шин и втычных контактов выдвижных частей НКУ (75 % случаев);
• перенапряжения, вызываемые разрушительными электрическими разрядами между точками с минимальными зазорами (15 % случаев);
• конструктивные дефекты аппаратуры (10 % случаев).
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
Англо-русский словарь нормативно-технической терминологии > arc fault
-
11 ISC
- ток короткого замыкания
- межсистемная связь
- международный центр коммутации
- международный коммутационный центр
- информация о пошагово управляемом положении
информация о пошагово управляемом положении
—
[ ГОСТ Р 54325-2011 (IEC/TS 61850-2:2003)]]Тематики
EN
международный коммутационный центр
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]Тематики
EN
международный центр коммутации
(МСЭ-T M.2100, МСЭ-Т I.358).
[ http://www.iks-media.ru/glossary/index.html?glossid=2400324]Тематики
- электросвязь, основные понятия
EN
межсистемная связь
—
[Е.С.Алексеев, А.А.Мячев. Англо-русский толковый словарь по системотехнике ЭВМ. Москва 1993]Тематики
EN
ток короткого замыкания
Сверхток, появляющийся в результате короткого замыкания, вызываемого повреждением или неправильным соединением в электрической цепи.
МЭК 60050(441-11-07)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
ток короткого замыкания
Сверхток, обусловленный замыканием с ничтожно малым полным сопротивлением между точками, которые в нормальных условиях эксплуатации должны иметь различный потенциал.
Примечание — Ток короткого замыкания может явиться результатом повреждения или неправильного соединения
(МЭС 441—11—07)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
ток короткого замыкания
Электрический ток в данной короткозамкнутой цепи.
[ ГОСТ Р МЭК 60050-195-2005]
ток короткого замыкания (Ic)
Сверхток, появляющийся в результате короткого замыкания, вследствие повреждения или неправильного соединения в электрической цепи
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
ток короткого замыкания
Электрический ток при данном коротком замыкании.
[ ГОСТ Р МЭК 60050-826-2009]
ток короткого замыкания
Сверхток, возникающий в результате короткого замыкания из-за дефекта или неправильного подключения в электрической цепи.
[ ГОСТ Р МЭК 60204-1-2007]EN
short-circuit current
an over-current resulting from a short circuit due to a fault or an incorrect connection in an electric circuit
[IEV number 441-11-07]
short-circuit current
electric current in a given short-circuit
Source: 603-02-28 MOD
[IEV number 195-05-18]
[IEV number 826-11-16]FR
courant de court-circuit
surintensité résultant d'un court-circuit dû un défaut ou à un branchement incorrect dans un circuit électrique
[IEV number 441-11-07
courant de court-circuit
courant électrique dans un court-circuit déterminé
Source: 603-02-28 MOD
[IEV number 195-05-18]
[IEV number 826-11-16]
Рис. 7 (Рис. ABB)
Контур тока короткого замыкания при замыкании на землю в системе ТТ
1 - Вторичная обмотка трансформатора;
2 - Линейный проводник;
3 - Сопротивление в месте замыкания;
4 - Проводник защитного заземления;
5 - Зазеамляющий электрод электроустановки;
6 - Заземляющий электрод нейтрали вторичной обмотки тарнсформатораПараллельные тексты EN-RU
An earth fault in a TT system originates the circuit represented in Figure 7.
The fault current flows through the secondary winding of the transformer, the line conductor, the fault resistance, the protective conductor, and the earth electrode resistances (RA, of the user’s plant, and RB, of the neutral).
[ABB]Замыкание на землю в системе TT образует цепь, представленную на рисунке 7.
Ток короткого замыкания протекает через вторичную обмотку трансформатора, линейный проводник, сопротивление в месте замыкания, проводник защитного заземления, заземляющие электроды (RA электроустановки и RB нейтрали вторичной обмотки трансформатора).
[Перевод Интент]Тематики
- электробезопасность
- электротехника, основные понятия
- электроустановки
EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > ISC
-
12 electric arc phenomenon
явление электрической дуги
-
[Интент]Параллельные тексты EN-RU
Electric arc phenomenon
The electric arc is a phenomenon which takes place as a consequence of a discharge which occurs when the voltage between two points exceeds the insulating strength limit of the interposed gas; then, in the presence of suitable conditions, a plasma is generated which carries the electric current till the opening of the protective device on the supply side.
Gases, which are good insulating means under normal conditions, may become current conductors in consequence of a change in their chemical-physical properties due to a temperature rise or to other external factors.
To understand how an electrical arc originates, reference can be made to what happens when a circuit opens or closes.
During the opening phase of an electric circuit the contacts of the protective device start to separate thus offering to the current a gradually decreasing section; therefore the current meets growing resistance with a consequent rise in the temperature.
As soon as the contacts start to separate, the voltage applied to the circuit exceeds the dielectric strength of the air, causing its perforation through a discharge.
The high temperature causes the ionization of the surrounding air which keeps the current circulating in the form of electrical arc. Besides thermal ionization, there is also an electron emission from the cathode due to the thermionic effect; the ions formed in the gas due to the very high temperature are accelerated by the electric field, strike the cathode, release energy in the collision thus causing a localized heating which generates electron emission.
The electrical arc lasts till the voltage at its ends supplies the energy sufficient to compensate for the quantity of heat dissipated and to maintain the suitable conditions of temperature. If the arc is elongated and cooled, the conditions necessary for its maintenance lack and it extinguishes.
Analogously, an arc can originate also as a consequence of a short-circuit between phases. A short-circuit is a low impedance connection between two conductors at different voltages.
The conducting element which constitutes the low impedance connection (e.g. a metallic tool forgotten on the busbars inside the enclosure, a wrong wiring or a body of an animal entered inside the enclosure), subject to the difference of potential is passed through by a current of generally high value, depending on the characteristics of the circuit.
The flow of the high fault current causes the overheating of the cables or of the circuit busbars, up to the melting of the conductors of lower section; as soon as the conductor melts, analogous conditions to those present during the circuit opening arise. At that point an arc starts which lasts either till the protective devices intervene or till the conditions necessary for its stability subsist.
The electric arc is characterized by an intense ionization of the gaseous means, by reduced drops of the anodic and cathodic voltage (10 V and 40 V respectively), by high or very high current density in the middle of the column (of the order of 102-103 up to 107 A/cm2), by very high temperatures (thousands of °C) always in the middle of the current column and – in low voltage - by a distance between the ends variable from some microns to some centimeters.
[ABB]Явление электрической дуги
Электрическая дуга между двумя электродами в газе представляет собой физическое явление, возникающее в тот момент, когда напряжения между двумя электродами превышает значение электрической прочности изоляции данного газа.
При наличии подходящих условий образуется плазма, по которой протекает электрический ток. Ток будет протекать до тех пор, пока на стороне электропитания не сработает защитное устройство.
Газы, являющиеся хорошим изолятором, при нормальных условиях, могут стать проводником в результате изменения их физико-химических свойств, которые могут произойти вследствие увеличения температуры или в результате воздействия каких-либо иных внешних факторов.
Для того чтобы понять механизм возникновения электрической дуги, следует рассмотреть, что происходит при размыкании или замыкании электрической цепи.
При размыкании электрической цепи контакты защитного устройства начинают расходиться, в результате чего постепенно уменьшается сечение контактной поверхности, через которую протекает ток.
Сопротивление электрической цепи возрастает, что приводит к увеличению температуры.
Как только контакты начнут отходить один от другого, приложенное напряжение превысит электрическую прочность воздуха, что вызовет электрический пробой.
Высокая температура приведет к ионизации воздуха, которая обеспечит протекание электрического тока по проводнику, представляющему собой электрическую дугу. Кроме термической ионизации молекул воздуха происходит также эмиссия электронов с катода, вызванная термоэлектронным эффектом. Образующиеся под воздействием очень высокой температуры ионы ускоряются в электрическом поле и бомбардируют катод. Высвобождающаяся, в результате столкновения энергия, вызывает локальный нагрев, который, в свою очередь, приводит к эмиссии электронов.
Электрическая дуга длится до тех пор, пока напряжение на ее концах обеспечивает поступление энергии, достаточной для компенсации выделяющегося тепла и для сохранения условий поддержания высокой температуры. Если дуга вытягивается и охлаждается, то условия, необходимые для ее поддержания, исчезают и дуга гаснет.
Аналогичным образом возникает дуга в результате короткого замыкания электрической цепи. Короткое замыкание представляет собой низкоомное соединение двух проводников, находящихся под разными потенциалами.
Проводящий элемент с малым сопротивлением, например, металлический инструмент, забытый на шинах внутри комплектного устройства, ошибка в электромонтаже или тело животного, случайно попавшего в комплектное устройство, может соединить элементы, находящиеся под разными потенциалами, в результате чего через низкоомное соединение потечет электрический ток, значение которого определяется параметрами образовавшейся короткозамкнутой цепи.
Протекание большого тока короткого замыкания вызывает перегрев кабелей или шин, который может привести к расплавлению проводников с меньшим сечением. Как только проводник расплавится, возникает ситуация, аналогичная размыканию электрической цепи. Т. е. в момент размыкания возникает дуга, которая длится либо до срабатывания защитного устройства, либо до тех пор, пока существуют условия, обеспечивающие её стабильность.
Электрическая дуга характеризуется интенсивной ионизацией газов, что приводит к падению анодного и катодного напряжений (на 10 и 40 В соответственно), высокой или очень высокой плотностью тока в середине плазменного шнура (от 102-103 до 107 А/см2), очень высокой температурой (сотни градусов Цельсия) всегда в середине плазменного шнура и низкому падению напряжения при расстоянии между концами дуги от нескольких микрон до нескольких сантиметров.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
Англо-русский словарь нормативно-технической терминологии > electric arc phenomenon
-
13 resonant earthed neutral system
система с компенсированной нейтралью
Система, в которой по крайней мере одна нейтральная точка заземлена через устройство, имеющее индуктивность, предназначенную для компенсации емкостных токов в случае единичного замыкания линейного (фазного) проводника на землю.
[ ГОСТ Р МЭК 60050-195-2005]EN
resonant earthed neutral system
system in which at least one neutral point is earthed through a device having an inductance designed to compensate approximately for the line-to-earth capacitances in case of a single-line-to-earth fault
[IEV number 195-04-09]FR
réseau à neutre compensé (par bobine d'extinction)
réseau dont au moins un point neutre est mis à la terre par l’intermédiaire d’un dispositif présentant une inductance conçue pour compenser approximativement les capacités ligne/terre en cas de défaut monophasé à la terre
[IEV number 195-04-09]Тематики
EN
- arc-suppression-coil-earthed neutral system
- arc-suppression-coil-grounded neutral system (US)
- resonant earthed neutral system
- resonant grounded neutral system (US)
DE
FR
электрическая сеть с компенсированной нейтралью
Электрическая сеть, содержащая оборудование, нейтрали которого, все или часть из них, заземлены через дугогасящие реакторы.
[ ГОСТ 24291-90]EN
resonant earthed (neutral) system
arc-suppression-coil-earth (neutral) system
a system in which one or more neutral points are connected to earth through reactances which approximately compensate the capacitive component of a single-phaseto-earth fault current
[IEV number 601-02-27]FR
réseau compensé par bobine d'extinction
réseau dont un ou plusieurs points neutres sont reliés à la terre par des réactances compensant approximativement la composante capacitive du courant de défaut monophasé à la terre
[IEV number 601-02-27]Тематики
EN
- arc-suppression-coil-earth neutral system
- arc-suppression-coil-earth system
- resonant earthed neutral system
- resonant earthed system
DE
- gelöschtes Netz
- Netz mit Erdschlusskompensation
- Netz, gelöschtes
FR
Англо-русский словарь нормативно-технической терминологии > resonant earthed neutral system
-
14 distributed neutral
система с нулевым рабочим проводником
-Рис. ABB
Система ТТПараллельные тексты EN-RU In TT systems the neutral and the exposed-conductiveparts are connected to earth electrodes electrically independent; therefore the earth fault current returns to the power supply node through the soil.
In this type of electrical installations the neutral is usually distributed and its function is making the phase voltage (e.g. 230 V) available for the supply of the single-phase loads of civil installations.
[ABB]В системах TT нулевой рабочий проводник и открытые проводящие части присоединены к разным заземляющим электродам, поэтому ток замыкания на землю возвращается к источнику питания через землю.
В электроустановках данного типа для распределения электроэнергии обычно применяют нулевой рабочий проводник, который совместно с линейными проводниками используется для питания однофазных нагрузок электроустановок жилых и общественных зданий напряжением, например, 230 В.
[Перевод Интент]For 3-pole circuit breakers used on 3-wire systems ( neutral not distributed), always set this value to 33 (see below) to avoid indications of a meaningless phase-to-neutral voltage.
[Schneider Electric]Если 3-полюсный автоматический выключатель используется в 3-проводной сети (т. е. без нулевого рабочего проводника), обязательно установите для этого параметра значение 33 (порядок настройки описан ниже), это исключит отображение параметра «фазное напряжение», не имеющего смысла в данном случае.
[Перевод Интент]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > distributed neutral
-
15 arc-suppression-coil-earth neutral system
электрическая сеть с компенсированной нейтралью
Электрическая сеть, содержащая оборудование, нейтрали которого, все или часть из них, заземлены через дугогасящие реакторы.
[ ГОСТ 24291-90]EN
resonant earthed (neutral) system
arc-suppression-coil-earth (neutral) system
a system in which one or more neutral points are connected to earth through reactances which approximately compensate the capacitive component of a single-phaseto-earth fault current
[IEV number 601-02-27]FR
réseau compensé par bobine d'extinction
réseau dont un ou plusieurs points neutres sont reliés à la terre par des réactances compensant approximativement la composante capacitive du courant de défaut monophasé à la terre
[IEV number 601-02-27]Тематики
EN
- arc-suppression-coil-earth neutral system
- arc-suppression-coil-earth system
- resonant earthed neutral system
- resonant earthed system
DE
- gelöschtes Netz
- Netz mit Erdschlusskompensation
- Netz, gelöschtes
FR
Англо-русский словарь нормативно-технической терминологии > arc-suppression-coil-earth neutral system
-
16 arc-suppression-coil-earth system
электрическая сеть с компенсированной нейтралью
Электрическая сеть, содержащая оборудование, нейтрали которого, все или часть из них, заземлены через дугогасящие реакторы.
[ ГОСТ 24291-90]EN
resonant earthed (neutral) system
arc-suppression-coil-earth (neutral) system
a system in which one or more neutral points are connected to earth through reactances which approximately compensate the capacitive component of a single-phaseto-earth fault current
[IEV number 601-02-27]FR
réseau compensé par bobine d'extinction
réseau dont un ou plusieurs points neutres sont reliés à la terre par des réactances compensant approximativement la composante capacitive du courant de défaut monophasé à la terre
[IEV number 601-02-27]Тематики
EN
- arc-suppression-coil-earth neutral system
- arc-suppression-coil-earth system
- resonant earthed neutral system
- resonant earthed system
DE
- gelöschtes Netz
- Netz mit Erdschlusskompensation
- Netz, gelöschtes
FR
Англо-русский словарь нормативно-технической терминологии > arc-suppression-coil-earth system
-
17 resonant earthed system
электрическая сеть с компенсированной нейтралью
Электрическая сеть, содержащая оборудование, нейтрали которого, все или часть из них, заземлены через дугогасящие реакторы.
[ ГОСТ 24291-90]EN
resonant earthed (neutral) system
arc-suppression-coil-earth (neutral) system
a system in which one or more neutral points are connected to earth through reactances which approximately compensate the capacitive component of a single-phaseto-earth fault current
[IEV number 601-02-27]FR
réseau compensé par bobine d'extinction
réseau dont un ou plusieurs points neutres sont reliés à la terre par des réactances compensant approximativement la composante capacitive du courant de défaut monophasé à la terre
[IEV number 601-02-27]Тематики
EN
- arc-suppression-coil-earth neutral system
- arc-suppression-coil-earth system
- resonant earthed neutral system
- resonant earthed system
DE
- gelöschtes Netz
- Netz mit Erdschlusskompensation
- Netz, gelöschtes
FR
Англо-русский словарь нормативно-технической терминологии > resonant earthed system
-
18 arc-proof low voltage switchgear and controlgear assembly
НКУ с защитой от воздействия электрической дуги
комплектное устройство с защитой от электрической дуги
низковольтное комплектное устройство с защитой от электрической дуги
НКУ распределения и управления с защитой от электрической дуги
-
[Интент]EN
arc-resistant switchgear
A type of switchgear design which is designed to withstand the effects of an internal arcing fault, without causing harm to personnel who are located in defined areas. It is not intended to withstand these internal arcing fault without possibly causing physical damage to the structure and/or components, but often the physical damage is less with an arc-resistant design.
There are three classes of protection:
Type A - eliminates the emission of gases and particles from the front of the switchgear during an internal arcing fault,
Type B - eliminates the emission of gases and particles from the front and sides of the switchgear during an internal arcing fault,
Type C - eliminates the emission of gases and particles from the front and sides of the switchgear, from between compartments within the same cell, and between adjacent cells during an internal arcing fault.
Arc-resistant switchgear has traditionally been metal-clad, but the basic concept could also be applied to other types of switchgear as well.
arc-proof switchgear
An incorrect term. Please refer to arc-resistant switchgear
[Schneider Electric]
[ http://electrical-engineering-portal.com/glossary-of-medium-voltage-switchgear-terms]Параллельные тексты EN-RU
If the electric arc occurs inside LV switchgear it generates internal overpressures and results in local overheatings which may cause high mechanical and thermal stresses in the equipment.
Besides, the involved materials can generate hot decomposition products, gases or fumes, which, due to the overpressure, are almost always ejected to the outside of the enclosure thus jeopardizing the operator safety.
The European Directive 2006/95/EC states the fundamental safety requirements for low voltage electric materials (from 50 V to 1000 V in alternating current, from 75 V to 1500 V in continuos current) to be put on the market within the European Community.
Among the essential safety requirements defined by this Directive particular importance is given to the need of taking technical measures to prevent “temperature rises, electric arcs or radiations which may result in hazards” from occurring.
This aspect has always been highly considered for apparatus, but it has been wrongly neglected for electrical switchgear and only in the last 10-15 years it has been catching on both at Italian as well as at international level.
Safety for the operator and for the installation in case of arcing inside LV switchgear can be obtained through three different design philosophies:
1. assemblies mechanically capable of withstanding the electric arc (passive protection)
2. assemblies equipped with devices limiting the effects of internal arcing (active protection)
3. assemblies equipped with current limiting circuitbreakers.
These three solutions (also combined together) have found a remakable development in the industrial field and have been successfully applied by the main manufacturers of LV switchgear and controlgear assemblies.
As it can be seen hereafter by examining the first two solutions, an “active” protection against arc faults is intrinsecally more complex than a “passive” one.
This because of the presence of additional electromechanical/ electronic devices5 which limit the arcing effects and which, by their nature, may be subject to faults or not-tripping.
[ABB]Дуга, возникшая внутри НКУ, создает внутреннее избыточное давление и вызывает локальный перегрев, что может привести к воздействию на оборудование значительного механического напряжения и перепада температур.
Кроме того, под воздействием дуги различные материалы разлагаются на продукты, имеющие высокую температуру, в том числе газы и дым, которые почти всегда вырываются из оболочки НКУ под высоким давлением, подвергая опасности оперативный персонал.
Европейская директива 2006/95/EC определяет основные требования безопасности для низковольтного (от 50 до 1000 В переменного тока и от 75 до 1500 В постоянного тока) оборудования поставляемого на рынок Европейского Сообщества.
Одно из основных требований безопасности, определяемое данной директивой как наиболее важное, заключается в необходимости предпринять технические меры для предотвращения "подъема температуры, возникновения электрической дуги или излучения", которые могут причинить ущерб.
Данная проблема всегда учитывалась при создании различных аппаратов, но незаслуженно игнорировалась при разработке электрических комплектных устройств, и только в последние 10-15 лет ей стали уделять должное внимание как в Италии, так и во всем мире.
При возникновении электрической дуги внутри НКУ безопасность оператора и электроустановки обеспечивается тремя способами:
1. Конструкция НКУ должна выдерживать механические воздействия, возникающие при горении электрической дуги (пассивная защита).
2. НКУ должно быть оснащено устройствами, ограничивающими воздействие электрической дуги (активная защита)
3. НКУ должны быть оснащены токоограничивающими автоматическими выключателями.
Указанные три способа (применяемые совместно) получили дальнейшее развитие в промышленности и успешно применяются основными изготовителями НКУ распределения и управления.
Как будет показано далее при рассмотрении первых двух способов, активная защита от дуговых» неисправностей является более сложной, чем пассивная защита.
Это объясняется необходимостью использования дополнительных электромеханических или электронных устройств, задачей которых является ограничение воздействий дуги и которые сами могут оказаться неисправными и не сработать.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Синонимы
- комплектное устройство с защитой от электрической дуги
- низковольтное комплектное устройство с защитой от электрической дуги
- НКУ распределения и управления с защитой от электрической дуги
EN
Англо-русский словарь нормативно-технической терминологии > arc-proof low voltage switchgear and controlgear assembly
-
19 arc-proof switchboard
НКУ с защитой от воздействия электрической дуги
комплектное устройство с защитой от электрической дуги
низковольтное комплектное устройство с защитой от электрической дуги
НКУ распределения и управления с защитой от электрической дуги
-
[Интент]EN
arc-resistant switchgear
A type of switchgear design which is designed to withstand the effects of an internal arcing fault, without causing harm to personnel who are located in defined areas. It is not intended to withstand these internal arcing fault without possibly causing physical damage to the structure and/or components, but often the physical damage is less with an arc-resistant design.
There are three classes of protection:
Type A - eliminates the emission of gases and particles from the front of the switchgear during an internal arcing fault,
Type B - eliminates the emission of gases and particles from the front and sides of the switchgear during an internal arcing fault,
Type C - eliminates the emission of gases and particles from the front and sides of the switchgear, from between compartments within the same cell, and between adjacent cells during an internal arcing fault.
Arc-resistant switchgear has traditionally been metal-clad, but the basic concept could also be applied to other types of switchgear as well.
arc-proof switchgear
An incorrect term. Please refer to arc-resistant switchgear
[Schneider Electric]
[ http://electrical-engineering-portal.com/glossary-of-medium-voltage-switchgear-terms]Параллельные тексты EN-RU
If the electric arc occurs inside LV switchgear it generates internal overpressures and results in local overheatings which may cause high mechanical and thermal stresses in the equipment.
Besides, the involved materials can generate hot decomposition products, gases or fumes, which, due to the overpressure, are almost always ejected to the outside of the enclosure thus jeopardizing the operator safety.
The European Directive 2006/95/EC states the fundamental safety requirements for low voltage electric materials (from 50 V to 1000 V in alternating current, from 75 V to 1500 V in continuos current) to be put on the market within the European Community.
Among the essential safety requirements defined by this Directive particular importance is given to the need of taking technical measures to prevent “temperature rises, electric arcs or radiations which may result in hazards” from occurring.
This aspect has always been highly considered for apparatus, but it has been wrongly neglected for electrical switchgear and only in the last 10-15 years it has been catching on both at Italian as well as at international level.
Safety for the operator and for the installation in case of arcing inside LV switchgear can be obtained through three different design philosophies:
1. assemblies mechanically capable of withstanding the electric arc (passive protection)
2. assemblies equipped with devices limiting the effects of internal arcing (active protection)
3. assemblies equipped with current limiting circuitbreakers.
These three solutions (also combined together) have found a remakable development in the industrial field and have been successfully applied by the main manufacturers of LV switchgear and controlgear assemblies.
As it can be seen hereafter by examining the first two solutions, an “active” protection against arc faults is intrinsecally more complex than a “passive” one.
This because of the presence of additional electromechanical/ electronic devices5 which limit the arcing effects and which, by their nature, may be subject to faults or not-tripping.
[ABB]Дуга, возникшая внутри НКУ, создает внутреннее избыточное давление и вызывает локальный перегрев, что может привести к воздействию на оборудование значительного механического напряжения и перепада температур.
Кроме того, под воздействием дуги различные материалы разлагаются на продукты, имеющие высокую температуру, в том числе газы и дым, которые почти всегда вырываются из оболочки НКУ под высоким давлением, подвергая опасности оперативный персонал.
Европейская директива 2006/95/EC определяет основные требования безопасности для низковольтного (от 50 до 1000 В переменного тока и от 75 до 1500 В постоянного тока) оборудования поставляемого на рынок Европейского Сообщества.
Одно из основных требований безопасности, определяемое данной директивой как наиболее важное, заключается в необходимости предпринять технические меры для предотвращения "подъема температуры, возникновения электрической дуги или излучения", которые могут причинить ущерб.
Данная проблема всегда учитывалась при создании различных аппаратов, но незаслуженно игнорировалась при разработке электрических комплектных устройств, и только в последние 10-15 лет ей стали уделять должное внимание как в Италии, так и во всем мире.
При возникновении электрической дуги внутри НКУ безопасность оператора и электроустановки обеспечивается тремя способами:
1. Конструкция НКУ должна выдерживать механические воздействия, возникающие при горении электрической дуги (пассивная защита).
2. НКУ должно быть оснащено устройствами, ограничивающими воздействие электрической дуги (активная защита)
3. НКУ должны быть оснащены токоограничивающими автоматическими выключателями.
Указанные три способа (применяемые совместно) получили дальнейшее развитие в промышленности и успешно применяются основными изготовителями НКУ распределения и управления.
Как будет показано далее при рассмотрении первых двух способов, активная защита от дуговых» неисправностей является более сложной, чем пассивная защита.
Это объясняется необходимостью использования дополнительных электромеханических или электронных устройств, задачей которых является ограничение воздействий дуги и которые сами могут оказаться неисправными и не сработать.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Синонимы
- комплектное устройство с защитой от электрической дуги
- низковольтное комплектное устройство с защитой от электрической дуги
- НКУ распределения и управления с защитой от электрической дуги
EN
Англо-русский словарь нормативно-технической терминологии > arc-proof switchboard
-
20 arc-proof switchgear
НКУ с защитой от воздействия электрической дуги
комплектное устройство с защитой от электрической дуги
низковольтное комплектное устройство с защитой от электрической дуги
НКУ распределения и управления с защитой от электрической дуги
-
[Интент]EN
arc-resistant switchgear
A type of switchgear design which is designed to withstand the effects of an internal arcing fault, without causing harm to personnel who are located in defined areas. It is not intended to withstand these internal arcing fault without possibly causing physical damage to the structure and/or components, but often the physical damage is less with an arc-resistant design.
There are three classes of protection:
Type A - eliminates the emission of gases and particles from the front of the switchgear during an internal arcing fault,
Type B - eliminates the emission of gases and particles from the front and sides of the switchgear during an internal arcing fault,
Type C - eliminates the emission of gases and particles from the front and sides of the switchgear, from between compartments within the same cell, and between adjacent cells during an internal arcing fault.
Arc-resistant switchgear has traditionally been metal-clad, but the basic concept could also be applied to other types of switchgear as well.
arc-proof switchgear
An incorrect term. Please refer to arc-resistant switchgear
[Schneider Electric]
[ http://electrical-engineering-portal.com/glossary-of-medium-voltage-switchgear-terms]Параллельные тексты EN-RU
If the electric arc occurs inside LV switchgear it generates internal overpressures and results in local overheatings which may cause high mechanical and thermal stresses in the equipment.
Besides, the involved materials can generate hot decomposition products, gases or fumes, which, due to the overpressure, are almost always ejected to the outside of the enclosure thus jeopardizing the operator safety.
The European Directive 2006/95/EC states the fundamental safety requirements for low voltage electric materials (from 50 V to 1000 V in alternating current, from 75 V to 1500 V in continuos current) to be put on the market within the European Community.
Among the essential safety requirements defined by this Directive particular importance is given to the need of taking technical measures to prevent “temperature rises, electric arcs or radiations which may result in hazards” from occurring.
This aspect has always been highly considered for apparatus, but it has been wrongly neglected for electrical switchgear and only in the last 10-15 years it has been catching on both at Italian as well as at international level.
Safety for the operator and for the installation in case of arcing inside LV switchgear can be obtained through three different design philosophies:
1. assemblies mechanically capable of withstanding the electric arc (passive protection)
2. assemblies equipped with devices limiting the effects of internal arcing (active protection)
3. assemblies equipped with current limiting circuitbreakers.
These three solutions (also combined together) have found a remakable development in the industrial field and have been successfully applied by the main manufacturers of LV switchgear and controlgear assemblies.
As it can be seen hereafter by examining the first two solutions, an “active” protection against arc faults is intrinsecally more complex than a “passive” one.
This because of the presence of additional electromechanical/ electronic devices5 which limit the arcing effects and which, by their nature, may be subject to faults or not-tripping.
[ABB]Дуга, возникшая внутри НКУ, создает внутреннее избыточное давление и вызывает локальный перегрев, что может привести к воздействию на оборудование значительного механического напряжения и перепада температур.
Кроме того, под воздействием дуги различные материалы разлагаются на продукты, имеющие высокую температуру, в том числе газы и дым, которые почти всегда вырываются из оболочки НКУ под высоким давлением, подвергая опасности оперативный персонал.
Европейская директива 2006/95/EC определяет основные требования безопасности для низковольтного (от 50 до 1000 В переменного тока и от 75 до 1500 В постоянного тока) оборудования поставляемого на рынок Европейского Сообщества.
Одно из основных требований безопасности, определяемое данной директивой как наиболее важное, заключается в необходимости предпринять технические меры для предотвращения "подъема температуры, возникновения электрической дуги или излучения", которые могут причинить ущерб.
Данная проблема всегда учитывалась при создании различных аппаратов, но незаслуженно игнорировалась при разработке электрических комплектных устройств, и только в последние 10-15 лет ей стали уделять должное внимание как в Италии, так и во всем мире.
При возникновении электрической дуги внутри НКУ безопасность оператора и электроустановки обеспечивается тремя способами:
1. Конструкция НКУ должна выдерживать механические воздействия, возникающие при горении электрической дуги (пассивная защита).
2. НКУ должно быть оснащено устройствами, ограничивающими воздействие электрической дуги (активная защита)
3. НКУ должны быть оснащены токоограничивающими автоматическими выключателями.
Указанные три способа (применяемые совместно) получили дальнейшее развитие в промышленности и успешно применяются основными изготовителями НКУ распределения и управления.
Как будет показано далее при рассмотрении первых двух способов, активная защита от дуговых» неисправностей является более сложной, чем пассивная защита.
Это объясняется необходимостью использования дополнительных электромеханических или электронных устройств, задачей которых является ограничение воздействий дуги и которые сами могут оказаться неисправными и не сработать.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Синонимы
- комплектное устройство с защитой от электрической дуги
- низковольтное комплектное устройство с защитой от электрической дуги
- НКУ распределения и управления с защитой от электрической дуги
EN
Англо-русский словарь нормативно-технической терминологии > arc-proof switchgear
- 1
- 2
См. также в других словарях:
Fault current limiter — A Fault Current Limiter (FCL) is a device which limits the prospective fault current when a fault occurs (eg in a power transmission network). The term is generally applied to superconducting devices, whereas non superconducting devices (such as… … Wikipedia
Current limiting — is the practice in electrical or electronic circuits of imposing an upper limit on the current that may be delivered to a load with the purpose of protecting the circuit generating or transmitting the current from harmful effects due to a short… … Wikipedia
Current sea level rise — This article is about the current and future rise in sea level associated with global warming. For sea level changes in Earth s history, see Sea level#Changes through geologic time. Sea level measurements from 23 long tide gauge records in… … Wikipedia
Fault indicator — A fault indicator is a device which provides visual indication of an electrical fault. They are used in electric power distribution networks as a means of automatically detecting and identifying faults. Basic principles During an electrical fault … Wikipedia
Fault (power engineering) — A fault is any abnormal situation in an electrical system in which the electrical current may or may not flow through the intended part/s.Fault is a condition when the current or voltage in any circuit do not flow in the same phase. in other… … Wikipedia
Residual-current device — A two pole residual current device A Residual Current Device is a generic term covering both RCCBs and RCBOs. A Residual Current Circuit Breaker (RCCB) is an electrical wiring device that disconnects a circuit whenever it detects that the… … Wikipedia
Alternating current — (green curve). The horizontal axis measures time; the vertical, current or voltage. In alternating current (AC, also ac) the movement of electric charge periodically reverses direction. In direct current (DC, also dc), the flow of electric charge … Wikipedia
Hayward Fault Zone — The Hayward Fault Zone is a geologic fault zone capable of generating significantly destructive earthquakes. About 60 kilometers long, it lies mainly along the western base of the hills on the east side of San Francisco Bay. It runs through… … Wikipedia
Arc-fault circuit interrupter — An arc fault circuit interrupter (AFCI) is a circuit breaker designed to prevent fires by detecting non working electrical arcs and disconnect power before the arc starts a fire. The AFCI should distinguish between a working arc that may occur in … Wikipedia
Transform fault — (the red lines) A transform fault or transform boundary, also known as conservative plate boundary since these faults neither create nor destroy lithosphere, is a type of fault whose relative motion is predominantly horizontal in either sinistral … Wikipedia
General Protection Fault (webcomic) — Infobox comic strip title= General Protection Fault caption= author= Jeffrey T. Darlington url= http://www.gpf comics.com/ rss= http://www.gpf comics.com/gpf.rss atom= status= Monday, Wednesday, Friday first= 1998 11 02 [http://www.gpf… … Wikipedia